UniPrint109 and UniPrint116 HSLA Support

The following videos will cover:
HSLA Overview
Loading labels on a HSLA
HSLA setup prior to production
UniPrint116 HSLA – Cleaning
UniPrint116 – SKB Shipping Crate
M8485 to S84 Conversion

---

• HSLA Overview
  
• Loading labels on a HSLA
  
• HSLA setup prior to production
  
• UniPrint116 HSLA – Cleaning
  
• UniPrint116 – SKB Shipping Crate
  
• M8485 to S84 Conversion
  

Each video below is demonstrated on either a HSLA or SSHSLA model, but the steps/procedures will be the same for all UniPrint models:
Print Engine Removal/Replacement
UniPrint116 – Air Assist Rod Replacement
UniPrint116 – Air Valve Replacement
UniPrint116 – Air Tubing Replacement
Regulator Replacement
Take Up Motor Replacement
Low Label Sensor Replacement
On/Off Switch Replacement and Testing

---

• Print Engine Removal/Replacement
  
• UniPrint116 – Air Assist Rod Replacement
  
• UniPrint116 – Air Valve Replacement
  
• UniPrint116 – Air Tubing Replacement
  
• Regulator Replacement
  
• Take Up Motor Replacement
  
• Low Label Sensor Replacement
  
• On/Off Switch Replacement and Testing
  

Each video below is demonstrated on either a Left Hand or Right Hand S84 Print Engine, but the steps/procedures will be the same for both models:
Label Offset
S84 Gap Sensor Calibration
Life and Head Count
Installing a Stage 1 Kit in a S84 Print Engine
Installing a Stage 2 Kit in a S84 Print Engine
Using an EXT DB-25 Tester on a S84 Print Engine
Tracking Collar Replacement
RFID Tuning Insert

---

• Label Offset
  
• S84 Gap Sensor Calibration
  
• Life and Head Count
  
• Installing a Stage 1 Kit in a S84 Print Engine
  
• Installing a Stage 2 Kit in a S84 Print Engine
  
• Using an EXT DB-25 Tester on a S84 Print Engine
  
• Tracking Collar Replacement
  
• RFID Tuning Insert
  

Each video below is demonstrated on either a Left Hand or Right Hand S84 Print Engine, but the steps/procedures will be the same for both models:
S84NX – Life and Head Count
S84NX – Offset Adjustment
S84NX – Stage 1 Kit
S84NX – Stage 2 Kit
S84NX – Gap and I-Mark Calibration

---

• S84NX – Life and Head Count
  
• S84NX – Offset Adjustment
  
• S84NX – Stage 1 Kit
  
• S84NX – Stage 2 Kit
  
• S84NX – Gap and I-Mark Calibration
  

The following photos display the UniPrint116 HSLA model. If a part is specific to a certain model (UniPrint109 or UniPrint116), the textbox will note both options and part numbers if applicable.

Hover over the teal dots to view spare parts and part numbers for the machine.

 

UniPrint116 HSLA RFID Printer

Coupa #7187254

Right Hand S84ex Stage 1 Kit

Coupa #7187291

S84ex Print Plate

Coupa #7121254

Right Hand S84ex Stage 2 Kit

Coupa #7187298

S84NX Stage 1 Kit

Coupa #7187471

   

S84NX Print Plate

Coupa #7187459

Right Hand S84NX Stage 2 Kit

Coupa #7187557

IMI Tool Kit

Coupa #7187286

IMI Sato S84 Tester

Coupa #7187391

EZ Wipes

Coupa #7186057

IMI Shipping Crate

Coupa #7187268

IMI Printer Cover

Coupa #7187271

View the pdf below to install the RFID tuning insert.

View the pdf below to adjust the Pressure Roller.

View the pdf below to calibrate the Gap and I-Mark Sensors.

View the pdf below to install the RFID tuning insert.

View the pdf below to correct RFID Encoding Failures.

View the pdf below to capture a Hex Dump. This dump can then be used to determine if there is a problem with the label data.

This overview provides operators with a step-by-step guide for properly loading, switching, and saving label profiles on the S84NX print engine.
It focuses on transitioning between Smart (thin) and Thick label stock profiles to ensure consistent print quality and reliable applicator performance.

*Please note that this may not be installed on every S84NX print engine.

View the pdf below for the process of converting the S84ex to an S84NX.

View the pdf below to make adjustments so that labels apply correctly.