The UniPrint109 and UniPrint116 HSLA models are side apply machines. The difference between the two models are the main board (blue vs red), the addition of the regulator, and the upgrade from the Norgren Valve to the MAC Valve.Â
This page will provide support with documentation, videos, and replacement parts for both the UniPrint109 and UniPrint116 models.Â
Would you like IMI to repair your Machine?
If you would like IMI to repair your machine, click here to view the process.
Documentation
UniPrint116 HSLA Operator Manual
UniPrint116 HSLA Wiring Diagram
Support QR Codes for UniPrint Models
HSLA RFID Recommended Spare Parts
Videos
The videos below give instruction on tasks necessary to maintain/operate Innovative Machine equipment.
The following videos will cover:
HSLA Overview
Loading labels on a HSLA
HSLA setup prior to production
UniPrint116 HSLA – Cleaning
UniPrint116 – SKB Shipping Crate
M8485 to S84 Conversion
- HSLA Overview
- Loading labels on a HSLA
- HSLA setup prior to production
- UniPrint116 HSLA – Cleaning
- UniPrint116 – SKB Shipping Crate
- M8485 to S84 Conversion
Each video below is demonstrated on either a HSLA or SSHSLA model, but the steps/procedures will be the same for all UniPrint models:
Print Engine Removal/Replacement
UniPrint116 – Air Assist Rod Replacement
UniPrint116 – Air Valve Replacement
UniPrint116 – Air Tubing Replacement
Regulator Replacement
Take Up Motor Replacement
Low Label Sensor Replacement
On/Off Switch Replacement and Testing
- Print Engine Removal/Replacement
- UniPrint116 – Air Assist Rod Replacement
- UniPrint116 – Air Valve Replacement
- UniPrint116 – Air Tubing Replacement
- Regulator Replacement
- Take Up Motor Replacement
- Low Label Sensor Replacement
- On/Off Switch Replacement and Testing
Each video below is demonstrated on either a Left Hand or Right Hand S84 Print Engine, but the steps/procedures will be the same for both models:
Label Offset
S84 Gap Sensor Calibration
Life and Head Count
Installing a Stage 1 Kit in a S84 Print Engine
Installing a Stage 2 Kit in a S84 Print Engine
Using an EXT DB-25 Tester on a S84 Print Engine
Tracking Collar Replacement
RFID Tuning Insert
- Label Offset
- S84 Gap Sensor Calibration
- Life and Head Count
- Installing a Stage 1 Kit in a S84 Print Engine
- Installing a Stage 2 Kit in a S84 Print Engine
- Using an EXT DB-25 Tester on a S84 Print Engine
- Tracking Collar Replacement
- RFID Tuning Insert
Each video below is demonstrated on either a Left Hand or Right Hand S84 Print Engine, but the steps/procedures will be the same for both models:
S84NX – Life and Head Count
S84NX – Offset Adjustment
S84NX – Stage 1 Kit
S84NX – Stage 2 Kit
S84NX – Gap and I-Mark Calibration
- S84NX – Life and Head Count
- S84NX – Offset Adjustment
- S84NX – Stage 1 Kit
- S84NX – Stage 2 Kit
- S84NX – Gap and I-Mark Calibration
Replacement Parts
The following photos display the UniPrint116 HSLA model. If a part is specific to a certain model (UniPrint109 or UniPrint116), the textbox will note both options and part numbers if applicable.
Hover over the teal dots to view spare parts and part numbers for the machine.
UniPrint116 HSLA RFID Printer
Coupa #7187254
Right Hand Stage 1 Kit
With Print Plate                     Without Print Plate
Coupa #7187291Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Coupa #7187296
       Â
S84 Print Plate
Coupa #7121254
Right Hand Stage 2 Kit
Coupa #7187298
IMI Tool Kit
Coupa #7187286
IMI Sato S84 Tester
Coupa #7187391
EZ Wipes
Coupa #7186057
IMI Shipping Crate
Coupa #7187268
IMI Printer Cover
Coupa #7187271
FAQs
S84-ex Print Engine
View the pdf below to install the RFID tuning insert.
HSLA Machine
View the pdf below to make adjustments so that labels apply correctly.